The Aspire Pockex is a must-have pocket AIO vape.
Available in a range of desirable colours including pink, chrome, black, white, blue, and rainbow.
Pocket Size Vape Perfection
Being just a bit shorter than the iPhone 5s, the Aspire PockeX is the ultimate pocket All-in-One (AIO) device. Packed with a 0.6Ω stainless steel U-Tech coil, the PockeX is an excellent sub-ohm device. The PockeX has a wider drip-tip and larger top-airflow allowing for increased vapour production.
The device has a 2ml (TPD compliant tank) built into the unit which is leak-resistant and very easy to fill and use. The device comes in a number of very attractive colours.
- Suitable for MTL or DL vaping
- It comes with a 0.6ohm sub-ohm U-Tech coil & 1.2ohm mouth to lung coil.
- The airflow is set in place to give the perfect draw required for these coils.
- If you need a stealthy sidekick to your current setup or are just starting out then look no further than this device.
- Perfect for vaping on the go !!
- E-liquids or Nic Salts
I have been using the 0.6ohm coil with 20mg nic salt liquids (Vape Dinner Lady) and it suits me fine. Good nicotine hit with little or no flavour loss.
Aspire Pockex Specification
High spec, easy to use vape pen
- Battery capacity – 1500mAh
- Tank capacity – 2.0ml
- Atomizer resistance – 0.6ohm / 1.2ohm
- Colours - Black, Stainless steel, Rose Gold, White, Blue or Rainbow.
- Dimensions – 19.7mm x 117.07mm
- You'll Receive
- 1 x Aspire PockeX UK AIO Kit
- 1 x 0.6ohm U-Tech coil pre-installed.
- 1 x Spare 1.2ohm U-Tech coil
- 1 x USB charging cable
- 1 x User manual
- Additional Info
Aspire PockeX Review - Office Favourite
I have been using the Aspire PockeX AIO vape device for the last six months while working from home.
I have a bad habit of chopping and changing from one device to another. Since I started using the PockeX I have found that it is my preferred daily vape. The Pockex isn't the smallest of pen vapes, it's a nice size, and superior quality touch to it. It feels weighty in the hand, not too heavy and not too bulky.
Charging the PockeX
Its handy USB charging means that I can leave it plugged into my laptop as I work. The pass-thru charging feature is great as it allows you to continue to vape whilst it's charging. Perfect for me because I spend hours at my computer.
The PockeX has a fast type C USB charging port that lights up red when charging and turns green when fully charged and ready for use, A full charge will usually last me about 7-8 hours but may vary depending on usage.
The PockeX is a simple button-fire device with a single large button just below the tank on the side of the device, The button has a nice positive click feel to it when operated. The button also features a background light to indicate when it is activated. The same light also indicates power level with two different colours, blue when it's charged, red when it's low power and requires charging. To turn on the device simply click the button 5 times in quick succession, to turn it off, just repeat the process.
Easy to fill
Featuring a top-fill tank, the Aspire PockeX is easy to top up with liquid. The cap screws down onto the top of the coil/atomiser. Some Reviewers have suggested inserting the coil first so that when you remove the top the coil would stay in place, this makes it easier to judge how much liquid you need to fill it. However, I have found that the coil sooner or later will end up attached to the cap, this isn't a problem as there is a handy 'fill' line on the tank beside the window. It just makes it a little more fiddly if you have to remove the cap with the coil, and don't have anywhere to put it down. Also, I'd recommend replacing the seal on the cap regularly as the constant filling can cause it to start leaking, not very handy if you carry it in your pocket or leave it laying on your desk.
Changing the coil/atomiser
As with re-filling the PockeX, replacing the coil/atomiser is super easy. Ensure that the device is turned off, 5 clicks in quick succession. If the coil is attached to the cap, simply unscrew it and replace it by screwing in the new one. If the coil is attached at the bottom, top of the battery unit, simply slide off the glass tank and metal protective sleeve which will allow full access to the coil, Replace the coil by first priming it, add a little e-liquid to the cotton through the small windows on each side of the coil, then screw it tightly to the base, replace the glass tank, ensuring it has a good seal on the base, and slide on the sleeve. Refill and screw on the cap. Important note: leave the PockeX to stand for about 10 minutes before you power on and use the device. I usually give a few strong sucks to draw the liquid through the coil before firing it up.
Using the PockeX
The Aspire PockeX comes with two coils, a sub-Ohm 0.6ohm U-tech coil ( pre-installed) and a spare 1.2ohm U-tech coil.
I have used the PockeX with both high nic e-liquids, typically 18mg and Salt Nic vape liquids and found that the 0.6ohm coil was especially suited to both for my style of vaping. The sub-ohm coil is aimed at vapers who like direct-to-lung or DL vaping but works perfectly for mouth-to-lung vapers or ML vaping. The 1.2ohm coil is aimed at ML vapers.
After accidentally burning out the 1.2ohm coil that was installed and getting some dry hits, a horrible taste in the mouth because I had burnt the cotton when the liquid ran down and the cotton was dry.
Not a producer of large vape clouds, the PockeX coils do produce a flavourful vape when using premium quality e-liquids like the Vape Dinner Lady range. I would definitely recommend the Aspire PockeX as a great vape starter kit for first-time vapours that are looking for a good quality vape device from a top brand.
Aspire PockeX User Manual (TPD English)
PockeX Top-Fill Instructions:
1. Unscrew and remove the top cap
2. Squirt your favorite E-Liquid into the tank ( Do not exceed the Max line when filling)
3. Screw the top cap to the PockeX tank
Important: When using the atomizer for the first time, make sure to let the E-liquid wick until the cotton is fully saturated before firing. This should take around 2-3 minutes according to E-Liquid thickness. This will ensure your atomizer does not burn out